Guides

Displaying 10 out of 25 suppliers

Spare Parts





Verification


Supplier specification


Class approved

Lubricating & Greasing Equipment Spare Parts Suppliers

Centralized lubricating and greasing systems usually stop because a metering or control component fails. In progressive divider block layouts, a single seized/blocked outlet can lock the divider sequence, so downstream points stop receiving lubricant until the blockage is cleared and the affected block section (or outlet check) is repaired or replaced. In single-line injector/parallel layouts, individual metering valves/injectors can stick or leak internally and stop dosing at a point even when line pressure exists.

Other common failures are mechanical and electrical: relief/safety valves that bypass at the wrong pressure (no effective line pressure), worn pump elements/seals (loss of output), damaged tubing/hoses/fittings from vibration and corrosion (loss of pressure or continuous leakage), and failed pressure/no-flow/cycle monitoring devices that trip alarms or shut the system down even after the mechanical fault is fixed.

These are the scenarios where keeping a small set of critical spares on board - and working with a lubricating and greasing equipment spare parts supplier who can match the exact part numbers and system configuration - reduces downtime and helps avoid installing unverified parts that don’t meter correctly.

Critical and Common Spare Parts for Lubricating and Greasing equipment

1. Pump unit and reservoir (highest priority spares)

  • Pump element(s) (piston/gear element, depending on model) and associated non-return valves
  • Relief valve / pressure-limiting components (often the root cause of no pressure)
  • Filters/strainers (suction strainer and any inline filters)
  • Seal kit (O-rings, gaskets, shaft seals) suited to the lubricant and temperature range
  • Motor/drive items where applicable: motor capacitor (single-phase), coupling, drive key; plus basic electrical consumables (fuses, terminals)

2. Metering and distribution hardware

  • For progressive divider block systems: one complete divider block (or at least the most high-wear sections), end sections, cross-port bridges/plugs, and outlet check assemblies
  • For injector / single-line parallel systems: a small set of injectors/metering valves in the common output sizes used on board, plus the matching check valves
  • Manifold blocks, restrictors (if used), and blanking plugs

3. Monitoring and controls

  • Low-level sensor (float/capacitive type as installed) and connector
  • Pressure switch/transducer used for alarm/trip logic
  • Cycle confirmation device where fitted (cycle switch, piston movement sensor, or visual indicator)
  • For controller-based systems: spare controller I/O fuse, relay, or a pre-configured spare module if the system is critical to operations

4. Lines, fittings, and point hardware (high consumption, low cost, high impact)

  • Assorted tubing, hoses, and the exact fitting types used (compression fittings, push-in, flare, etc.)
  • Bulkhead fittings, elbows, tees, and caps (corrosion and vibration are constant)
  • Grease nipples (straight and angled) in the common thread sizes on the vessel
  • A few high-risk items: quick fill coupling seals, hose swivel seals, protective caps for exposed points

5. Practical stocking rules that reduce downtime

  • Keep critical lubrication spares grouped so a failure can be fixed without searching across stores for matching fittings, seals, or the correct metering parts.
  • Keep spares clean, sealed, and labeled; contamination introduced during replacement can create repeat failures.
  • Standardize where possible (same nipple/thread type, same tubing size, same injector outputs) to reduce part variety.

When you need a replacement part, it’s worth taking two minutes to confirm the exact configuration of the installed unit - because many lubrication components are sold in multiple variants that look similar but behave differently in service (metered output, pressure rating, voltage/connector, thread type, etc.). A practical way is to pull the manual/parts list that matches the pump’s model code and serial, then cross-check the identifiers on the actual hardware (for example, progressive divider blocks are typically specified by part number/identification and can be supplied with different thread standards and metering quantities; injectors are also size-coded to deliver different volumes).

  • Japan Marine (S) Pte ltd logo

    Year Founded: 2011

    Verified

    Japan Marine (S) Pte ltd

    Verified

    We have listed our Key Strength Equipments as below for easy reference. We are strong in Main engines Aux Engines /Generators Compressors Main Air , Breathing , Refrigeration, Marine Pumps Purifiers /Separator Hatch Cover Spares / Hydraulic spares Electrical Hydraulic Motors Air horns Toilet Vacuum Systems Electrical spares and small components A/C Compressors HVAC system spares Boiler and Incinerators https://jmsgroup.jp/products/

    jmsgroup.jp
    operations@jmsgroup.jp

    CATEGORIES:

    • Lubricating & Greasing Equipment

    • 15 PPM Monitoring Equipment

    • AIS (Automatic Identification Systems)

    • AMS (Alarm Monitoring Systems)

    • ARPA (Automatic Radar Plotting Aids)

      (177)

    BRAND:

    • DEXTER

    • Graco

    • SKF

    • Dropsa

    • perma-tec

      (28)

    CLASS APPROVED:

    • DNV

    WAREHOUSES:

    • Singapore

    • United Arab Emirates

    • Angola

    • Austria

    • Australia (209)

  • ARK MARINE SERVICE INC. logo

    Year Founded: 2004

    Verified

    Verified

    We specialize in providing original equipment supplies, primarily for main and auxiliary engine spares. As a factory-based company, we ensure the best pricing without compromising on quality. Our dedicated logistics team handles all deliveries efficiently, offering competitive rates for air, sea, and courier services.

    CATEGORIES:

    • Lubricating & Greasing Equipment

    • 15 PPM Monitoring Equipment

    • AIS (Automatic Identification Systems)

    • AMS (Alarm Monitoring Systems)

    • ARPA (Automatic Radar Plotting Aids)

    • AUS (Automatic Unloading Systems)

    • Accommodation Ladder Davits

    • Accomodation Ladders & Gangways

    • Air Compressors

    • Air Driven Motors

    • Air Horns

    • Air Reservoirs

    • Air Starters

    • Alpha Lubrication Systems

    • Anemometers

      (162)

    CLASS APPROVED:

    • ClassNK

    • BV

  • MARINE INDUSTRIAL GROUP LIMITED logo

    Year Founded: 2025

    Verified

    Verified

    SUPPLIER OF OEM , ORIGINAL , OR SECOND HAND OF MARINE PARTS -Marine oil Lubricants -Marine Engines -Pumps -Main Engine -Auxiliary Engine/Generator -Engine Spares -Propeller -Hydraulics -Pumps Spares -Oil Purifier Spares -Heat Exchanger -Air Compressors Spares -Turbo Chargers Spares Marine Industrial Group: Excellence in Marine Solutions With a commitment to superior service and quality products, Marine Industrial Group is your go-to source for marine engineering supplies. We specialize in ship spare parts and auxiliary systems. MIG- Marine Industrial Group Limited

    CATEGORIES:

    • Lubricating & Greasing Equipment

    • 15 PPM Monitoring Equipment

    • AIS (Automatic Identification Systems)

    • AMS (Alarm Monitoring Systems)

    • ARPA (Automatic Radar Plotting Aids)

    • AUS (Automatic Unloading Systems)

    • Accommodation Ladder Davits

    • Accomodation Ladders & Gangways

    • Air Compressors

    • Air Driven Motors

    • Air Horns

    • Air Reservoirs

    • Air Starters

    • Alpha Lubrication Systems

    • Anemometers

      (166)

    WAREHOUSES:

    • Hong Kong

  • Focus Marine Ltd. logo

    Year Founded: 2020

    RM verified

    RM verified

    We supply marine spare parts as our core business from our reliable partners/makers all over the World. Our parts are equivalent products NON-GENUINE unless otherwise stated. A part of scope of supply mentioned below as per engine types. 5L16/24, 5L21/31, 6L23/30H, 8L23/30, 5L28/32H, 7L32/40, 16V32/40-Non CD 16V32/40-CD, 6S60 MC-C, 7S60MC-C Mk7 6N18AL-V, 6N21AL-SV, 6DK20 TC : TCA66, TCA44, NR34/S148, NR20/R, RH183, TPL67-C33 SPARE PARTS : 2/4 STROKE ENGINE SPARE PARTS - MAN BW MAN SULZER WARTSILA KOBE AKASAKA DAIHATSU YANMAR HANSHIN HIMSEN - CUMMINS TURBOCHARGERS - IHI, MITSUBISHI, MAN, NAPIER, ABB, KBB AIR COMPRESSORS - TANABE, YANMAR, SPERRE, SAUER, TEIKOKU, TAMROTOR SEPARATOR - ALFA LAVAL, WESTFALIA, MITSUBISHI PUMPS - ALLWEILER, NANIWA, DESMI, SHINKO, TEIKOKU, ISHII, SHIN SHIN PHE SPARE PARTS - SWEP, TRANTER, SONDEX, ALFA LAVAL, GEA, APV, HISAKA FILTERS - BOLL KIRCH, MOATTI

    CATEGORIES:

    • Lubricating & Greasing Equipment

    • Air Compressors

    • Air Driven Motors

    • Air Horns

    • Air Starters

    • Alpha Lubrication Systems

    • Automation Control Equipment & Control Units

    • BackWash Filters

    • Boiler Automation Equipment

    • Centrifugal Pumps

    • Control Air Dryers

    • Cranes

    • Diesel Generators

    • Distance Rings & Spacer Rings for Stern Tube

    • Engine Fuel Injection High Pressure Pipes (2-Strok

      (66)

    WAREHOUSES:

    • Turkey

    • China

    • Greece

    • Japan

    • South Korea (1)

  • NEW CHANNEL CHINA INTERNATIONAL CO LTD logo

    Year Founded: 2010

    RM verified

    RM verified

    SHIP SPARE PARTS, SHIP EQUIPMENT, ALTERNATIVE SOLUTIONS, SHIP REPAIR, INSPECTION SERVICES, SHIP REPAIR BROKER, OFFSHORE EQUIPMENT, CONSUMERABLES, PROVISIONS, ON-SITE SUPPLY SERVICE PROVIDER, TECHNICAL TEAM FOR ASSISTANCE

    CATEGORIES:

    • Lubricating & Greasing Equipment

    • 15 PPM Monitoring Equipment

    • Accommodation Ladder Davits

    • Accomodation Ladders & Gangways

    • Air Compressors

    • Air Driven Motors

    • Air Horns

    • Air Reservoirs

    • Air Starters

    • AIS (Automatic Identification Systems)

    • Alpha Lubrication Systems

    • AMS (Alarm Monitoring Systems)

    • Anemometers

    • Anti-Heeling Systems

    • ARPA (Automatic Radar Plotting Aids)

      (166)

    CLASS APPROVED:

    • ABS

    • RINA

    • RMRS

    • ClassNK

    • CCS

      (11)

  • SEASTAR (HK) TRADE LIMITED logo

    Year Founded: 2018

    providing original spare parts for main engines, auxiliary machinery, engine room equipment, and deck auxiliary systems to domestic and international shipowners and management companies. competitive pricing Our global service network and professional logistics team ensure timely delivery of your spare parts to designated ports and destinations. Heat Exchanger Galley Equipment Electric motor Deck Crane Grab Windlass Mooring Winch Hatch Cover Gangway Ladder Winch Steering Gear Pintle Bush Synthetic Phenol Resin Valve Fire Alarm Detector Navigation Communication Equipment Water Ingress Alarm System Electrical Instrument and Automation Fuel Valve Test Device Main Engine Auxiliary Engine Turbocharger Air Compressor M/E Auxiliary Blower Pumps Boiler Incinerator Fresh Water Generator Oily-water Separator Sewage Water Treatment Plant 15ppm Bilge Alarm Fuel Oil supply Module Purifier Refrigeration and Air Conditioning

    CATEGORIES:

    • Lubricating & Greasing Equipment

    • 15 PPM Monitoring Equipment

    • AIS (Automatic Identification Systems)

    • AMS (Alarm Monitoring Systems)

    • ARPA (Automatic Radar Plotting Aids)

      (195)

    BRAND:

    • DEXTER

    • Graco

    • SKF

    • Dropsa

    • perma-tec

      (28)

    CLASS APPROVED:

    • ABS

    • ClassNK

    • CCS

    • BV

    WAREHOUSES:

    • China

  • international marine office logo

    Year Founded: 2014

    Welcome to International Marine Office IMO The Integrated Partner for Maritime Offshore Excellence Welcome to International Marine Office IMO, your comprehensive strategic partner providing full-spectrum solutions across the entire maritime and offshore lifecycle. We are a globally recognized force in engineering, construction, and operational support, committed to driving efficiency and sustainability for our clients. International Marine Office IMO, a powerhouse in the global maritime sector, specializing in delivering comprehensive solutions from design to delivery and throughout the operational lifecycle of your vessel. For over than 20 years experience, IMO has been the trusted name for clients demanding reliability, innovation, and integrated service excellence. Our expertise is built upon a foundation of deep technical knowledge across all phases of the marine industry:

    CATEGORIES:

    • Lubricating & Greasing Equipment

    • 15 PPM Monitoring Equipment

    • AIS (Automatic Identification Systems)

    • AMS (Alarm Monitoring Systems)

    • ARPA (Automatic Radar Plotting Aids)

    • AUS (Automatic Unloading Systems)

    • Accommodation Ladder Davits

    • Accomodation Ladders & Gangways

    • Air Compressors

    • Air Driven Motors

    • Air Horns

    • Air Reservoirs

    • Air Starters

    • Alpha Lubrication Systems

    • Anemometers

      (168)

    WAREHOUSES:

    • Egypt

  • SOVHAN MARINE SYNDICATE logo

    Year Founded: 1998

    Trusted exporter and reseller of genuine OEM and quality used ship spare parts. All items are carefully sourced from ship demolition yards, thoroughly overhauled, and tested to ensure reliable performance.

    CATEGORIES:

    • Lubricating & Greasing Equipment

    • 15 PPM Monitoring Equipment

    • AIS (Automatic Identification Systems)

    • AMS (Alarm Monitoring Systems)

    • ARPA (Automatic Radar Plotting Aids)

    • AUS (Automatic Unloading Systems)

    • Accommodation Ladder Davits

    • Accomodation Ladders & Gangways

    • Air Compressors

    • Air Driven Motors

      (161)

    CLASS APPROVED:

    • ABS

    • ClassNK

    • BV

    • LR

    • DNV

      (1)

    WAREHOUSES:

    • Bangladesh

  • DIESEL PARTNERS COREA CO.LTD logo

    Year Founded: 2013

    1. marine engine spare parts 1.1. MAIN ENGINE 1.1.1. 2 stroke engine spare parts - MAN, WARTSILA, MITSUBISHI, HANSHIN etc. 1.2. AUX. ENGINE 1.2.1. 4 stroke engine spare parts - MAN Holeby, YANMAR, DAIHATSU etc. 1.3. TURBOCHARGER 1.3.1. MAN Tubocharger major components additionally IHI, MET, ABB Turbocharger etc. 1.4. GENERATOR SET 1.4.1. MARINE 1.4.2. MARINE EMERGENCY 1.4.3. STATIONARY 1.4.4. ALTERNATOR 2. AUXILIARY MACHINERIES PARTS AS PER CONTENTS IN OUR WEBSITE 3. EXPERT LOGISTICS SERVICES

    CATEGORIES:

    • Lubricating & Greasing Equipment

    • 15 PPM Monitoring Equipment

    • AIS (Automatic Identification Systems)

    • AMS (Alarm Monitoring Systems)

    • ARPA (Automatic Radar Plotting Aids)

    • AUS (Automatic Unloading Systems)

    • Accommodation Ladder Davits

    • Accomodation Ladders & Gangways

    • Air Compressors

    • Air Driven Motors

      (172)

    CLASS APPROVED:

    • DNV

    WAREHOUSES:

    • South Korea

  • BestBangla Marine and Trading Ltd logo

    Year Founded: 2024

    Ship Spare Parts Support Export At BestBangla Marine Trading Ltd., we specialize in the prompt and reliable supply of genuine and OEM ship spare parts for all major engine types and marine equipment. With a deep understanding of vessel technical needs, we ensure timely delivery of quality-tested componentsnew and reconditionedto keep your operations running smoothly. We provide global export solutions tailored to ship owners, managers, and technical departments, with a focus on transparency, traceability, and technical precision. From main engine parts to navigation and safety systems, our inventory is supported by professional sourcing, certified inspections, and efficient logistics. Reliable sourcing. Global delivery. Technical assurance. Your trusted partner in marine spare parts excellence.

    CATEGORIES:

    • Lubricating & Greasing Equipment

    • 15 PPM Monitoring Equipment

    • AIS (Automatic Identification Systems)

    • AMS (Alarm Monitoring Systems)

    • ARPA (Automatic Radar Plotting Aids)

    • AUS (Automatic Unloading Systems)

    • Accommodation Ladder Davits

    • Accomodation Ladders & Gangways

    • Air Compressors

    • Air Driven Motors

      (171)

    CLASS APPROVED:

    • RINA

    • ClassNK

    • CCS

    • BV

    • CRS

      (8)

    WAREHOUSES:

    • Bangladesh